5 products
Popular models: Programmer J-Link BASE Compact 8.19.00, Programmer J-LINK V9, J-Link PLUS Classic development chip
Take avionics design and repair to the next level. J-Link programmers and development chips are professional-grade tools. They allow you to flash, debug and test microcontrollers. These devices are indispensable for in-depth work with flight controllers. You will be able to update the firmware and fix complex software errors.
High speed flashing and debugging for ARM processors.
Broad compatibility with thousands of microcontrollers.
Stable operation and reliable connection with the target device.
Support for modern debugging interfaces (SWD, JTAG).
Integration with popular development environments (Keil, IAR, Segger Embedded Studio).
J-Link acts as an intelligent intermediary between the PC and the target board. It connects to the computer via a USB interface. On the other hand, it connects to the debugging pins of the microcontroller. Most often via the SWD (Serial Wire Debug) or JTAG protocol.
The programmer performs several critical functions. It transfers the compiled firmware file from the software to the PC. Writes this file to the flash memory of the microcontroller on the board. Allows you to perform step-by-step debugging of a running program. You can stop the code, view registers and variables.
The range includes several lines for different tasks.J-Link BASEis a classic and popular model. It supports JTAG speeds up to 12 MHz and SWD speeds up to 8 MHz. Works with target device voltages from 1.2V to 3.3V. Ideal for most ARM controllers in drones.
More advanced version -J-Link PLUS. It offers increased firmware speed. It also supports additional interfaces such as SPI for external memory. This is important for working with controllers that have a bootloader via flash memory.
For the most demanding tasks there isJ-Link ULTRA+. Its speed reaches 50 MHz for JTAG and 40 MHz for SWD. This significantly reduces the time it takes to flash large files. And speeds up the process of iterative development and debugging.
Separately, it is worth noting the compactJ-Link EDUAndJ-Link OB(On-Board). The latter are often built directly into development boards. But to work with ready-made flight controllers, you need an external programmer.
The J-Link programmer provides access to the inner world of the microcontroller. Through it you can not only download firmware. But also read protected registers and do a memory dump. This is invaluable when diagnosing faults.
You can set a breakpoint anywhere in the code. When the program execution reaches it, the processor will stop. You will see the state of all systems at that specific moment. This is the best way to find the cause of a crash or misbehavior.
Trace is supported for some processors. It allows real-time recording of executed instructions. Or the values of key variables. After a drone accident, this helps to reconstruct the picture of the incident.
In hobby and professional development, J-Link is indispensable. When creating custom firmware for flight controllers (for example, Betaflight). For flashing brick boards that are not detected via USB. For deep debugging of problems with gyroscopes, timers, interrupts.
It is necessary to restore boards after an unsuccessful update. And also for direct flashing of external memory (SPI Flash) on some VTX or cameras. When developing your own devices on STM32 or other ARM chips.
It can be used to analyze why the drone is behaving strangely. For example, due to noise in the power supply or errors in filtering algorithms. This is a tool not for the average user, but for the engineer and enthusiast.
To connect you will need an adapter cable or socket. The standard interface is a 20-pin IDC connector on the programmer itself. There are usually 4-5 wires leading to the flight controller: VCC, GND, SWDIO, SWCLK, RESET.
It is important to correctly identify these pins on the controller board. Their location can be found in the documentation (datasheet) for the chip. Often they are signed on the board itself: SWD, JTAG, NRST.
After physical connection, you need to install drivers and software. Segger provides a free J-Link Software Pack. It includes command line utilities and DLLs for development environments.
The main utility for work isJ-Flash. This is a program for fast and reliable firmware download. Here you need to select the model of the target microcontroller. Upload the HEX or BIN firmware file. And press the programming button.
For debugging, an environment that supports the J-Link GDB server is used. For example, PlatformIO, Arduino IDE (with plugins) or professional Keil/IAR. J-Link acts as a hardware debugger in this environment.
UtilityJ-Link Commanderallows you to work directly through the command line. Useful for automation and script control of the firmware process.
Original J-Link programmers from Segger are the standard of reliability. They are characterized by stable connection and long service life. Supported by the manufacturer, software updates are released regularly.
They are used by leading companies in the mass production of electronics. This is an industrial tool that can handle intense workloads. An investment in such a programmer pays off in time and nerves saved.