What a Link Budget Is, in Plain Language
A link budget is the bookkeeping of every decibel that enters or leaves the radio path between your transmitter and the receiver on the aircraft. It starts with the power you send out, adds the gain of your antennas, subtracts the loss in your coax cables, subtracts the loss as the signal travels through air, and compares what arrives to the weakest signal the receiver can still decode. If the number that arrives is above that threshold, you have a link. If it dips below, you have a failsafe.
You do not need to run the math for every flight, but understanding which terms are in the equation tells you where the lever is when range disappoints. A surprising amount of "short range" problems are not solved by buying a more powerful transmitter. Browse the antennas and receivers catalogs to see the component classes this explainer refers to.
The Five Terms That Decide Your Range
Transmit power (TX power)
This is the watts, expressed in dBm, that leaves the transmitter antenna connector. Every doubling of transmit power adds about 3 dB. Cranking a transmitter from 25 mW to 100 mW is a 6 dB change, which is meaningful but finite. Regulated bands also cap transmit power in most jurisdictions, so there is a ceiling on how much this lever can pull.
Receiver sensitivity (RX sensitivity)
This is the weakest signal the receiver can still decode, expressed as a negative dBm number. A receiver that can decode -100 dBm hears twice as far as one that needs -94 dBm, all else equal, because that 6 dB difference means the path loss can be twice as large. Sensitivity is set by the receiver hardware, not by the pilot.
Antenna gain
A directional antenna focuses energy in one direction instead of radiating it evenly. A patch or a yagi on the ground adds gain measured in dBi, which directly improves the link in the direction the antenna is pointed. Omnidirectional antennas have near-zero gain but radiate in all directions, which is what makes them forgiving when the aircraft is all around you.
Cable and connector loss
Every coax pigtail, every U.fl connector, every extension between the radio and the antenna loses signal. Short coax is good coax. A pigtail that looks tidy but runs 20 cm of thin coax can cost you more dB than the antenna gains.
Free-space path loss and fading
As the signal travels through air, it spreads out and loses power with distance. Add reflections off terrain, foliage, buildings and the aircraft itself, and you have a fading environment rather than a clean line of sight. This is the term you cannot directly control, which is why the other four terms exist to build margin.
Why dB Numbers Sound Small but Matter
A decibel (dB) is a ratio, not a unit of power. The reason RC pilots talk in dB is that every lever in the link budget is a ratio: double the power is +3 dB, halve the loss is +3 dB, add a 6 dBi antenna is +6 dB.
This is why a "small" 2 dB difference between two antennas can feel huge in the air, and why routing a coax run 10 cm shorter can sometimes change whether your link survives a far-out mission. When you read spec sheets, compare dB numbers rather than watts, because watts only tell half the story.
Antenna Gain vs Antenna Pattern
Gain is only half the antenna story. The other half is the radiation pattern, which tells you in which directions that gain actually exists.
Omnidirectional antennas
An omnidirectional antenna radiates roughly evenly around its axis. It gives up gain for coverage: the aircraft can be anywhere around you and the link stays consistent. This is why the default on most handset transmitters is an omni, and why the default on the aircraft is an omni.
Directional antennas (patch, yagi)
A patch or yagi focuses energy forward. A 12 dBi patch gives you 12 dB of gain in a narrow cone in front of it, but almost nothing to the sides or behind. Directional antennas are excellent for long-range missions where you can point the antenna at the aircraft, but they require the pilot to steer the antenna like a spotlight.
Polarization
Antennas are either linearly polarized (vertical or horizontal) or circularly polarized. If the aircraft antenna and the pilot antenna are not matched in polarization, you lose several dB. Circular polarization is more forgiving because reflections rotate the polarization, which is why FPV video antennas often favor circular designs.
The Common Range Mistakes
Buying more transmit power without fixing coax loss
A 100 mW transmitter with a 3 dB coax loss delivers 50 mW equivalent to the antenna. A 25 mW transmitter with clean, short coax and a good antenna often outperforms it.
Running a high-gain directional antenna on the aircraft
A directional antenna on the aircraft only works if you can guarantee the aircraft always flies pointed at you. It cannot. Directional gain belongs on the ground station, not on the airframe.
Ignoring the aircraft-side antenna
Pilots optimize the ground station and forget the antenna on the drone. A tiny, damaged or poorly mounted aircraft antenna eats the dB you just spent on the ground.
Forgetting regulatory power limits
Most RC bands have legal transmit power limits. Cranking past them is not just unwise; it can cause interference and legal exposure. Build margin through antennas and placement, not through unregulated power.
How the Video Link Differs From the Control Link
FPV video on 5.8 GHz is a separate link from the control link (which usually runs on 2.4 GHz or 900 MHz). The same link-budget logic applies, but the numbers differ.
5.8 GHz video
Higher frequency means more bandwidth for high-definition video, but the path loss is steeper with distance. Video link problems usually show up as noise, loss of picture or break-up long before the control link drops. Directional 5.8 GHz FPV patch antennas are common on the ground station precisely because the video link benefits from focus.
Control link on 2.4 GHz or 900 MHz
Lower frequency means more range for the same power, which is why control links use it. The control link is designed to be resilient even when the video picture is gone. A good pilot habit is to trust the control link's RSSI over the video picture quality when deciding whether to turn back.
Building Margin Into Your Setup
A link budget is not a target; it is a margin. You want the link to survive the unexpected: a sudden tree line, a signal reflection off a hill, a battery sag that drops transmitter power.
Frequently Asked Questions
Does a higher dBm transmitter always give more range?
Not always. If your transmitter is already at the legal limit or if coax loss on the other side of it eats the gain, more power does not translate to more range. Build margin through antennas and placement first.
What is a good RSSI value to aim for?
It depends on the receiver's sensitivity. The right way to read RSSI is to compare it to the receiver's spec sheet, not to a generic number. A margin of several dB above the sensitivity floor at your farthest planned distance is a reasonable target.
Is a directional antenna better than an omni for long range?
For a fixed direction, yes. But it only works while you can point it. If you cannot steer the antenna, an omni with good placement often beats a mis-pointed directional.
Why does video break up before control?
Because 5.8 GHz video has higher bandwidth and steeper path loss than the 2.4 GHz or 900 MHz control link. The control link is designed to degrade gracefully, while video degrades visibly.
Can I amplify the video signal with an external amplifier?
Sometimes, but it must be matched to the band and power level. A poorly chosen amplifier can cause interference, violate regulatory limits and damage the VTX. Treat amplifiers as part of the link budget, not as a magic add-on.


